Aluminum Conduit For Cabling Channel Latching Cable Raceway
Aluminum Conduit for Cabling and Latching Cable Raceway
This latching cable raceway is extruded from aluminum and forms a closed channel for routing electrical and data cabling along walls, frames and machine surfaces. A U-shaped base pairs with a snap-on cover, so conductors stay enclosed yet remain easy to reach when a circuit is added or inspected.
Extruded Aluminum Channel Construction
The body is produced by hot extrusion, pressing heated aluminum billet through a shaped die to form a continuous profile with uniform wall thickness. The one-piece section has no longitudinal weld along the channel floor. Aluminum is chosen for its strength-to-weight ratio, which matters on lightweight frames and suspended ceilings.
Latching Cover and Access
The cover engages the base along a continuous lip and is pressed down until the halves seat. No separate fasteners are needed along the run, which speeds installation and removes the risk of loose screws dropping into a machine cavity. A flat blade inserted at the seam lifts the latch.
- Snap-fit cover with continuous lip engagement
- Tool-free opening along the full length
- Flat internal floor for cable laying
- Straight sections butt-joined for long runs
Sizes and Configurations
Channels are offered in a range of widths and heights so a chosen cable bundle fits without pinching. The internal cross-section must clear the largest connector on the run, not just the cable diameter, and a fill allowance near forty percent leaves room for later additions. Lengths cut on site should have the cut end deburred so insulation is not nicked while pulling.
Typical Applications
The profile suits cabling that must be contained but still reachable:
- Structured cabling and network risers in commercial interiors
- Control and power wiring on automation and test equipment
- Lighting circuits along display frames and shelving
- Conduit runs on tents, canopies and portable structures
Installation Notes
Support spacing should be set so the channel does not sag between fixings, and direction changes are handled with corner pieces or mitred cuts. Because aluminum conducts, the channel should not serve as an earthing conductor unless a qualified person confirms continuity and bonding for that installation.
Quality Control
Sections are checked for straightness, wall thickness and latch fit before packing. Each run is assembled dry to confirm the cover seats along its whole length.
Ordering Information
Confirm profile width, height, wall thickness, length, surface finish and quantity when enquiring, plus any corner or mounting accessory required.
Material & Temper | Aluminum Alloy 6063-T5,6061-T6 |
Surface Treatment | Anodizing, powder coating, electrophoresis, wood grain, polishing, brushing, sandblasting, etc. |
Colour | Silver |
Grade | 6000 series |
Weight | 0.94kg/m |
Mass of Inertia | lx: 3.80 cm4 ly: 4.60 cm4 |
Section Modulus | zx: 0 cm3 zy: 0 cm3 |
Slot width | 10.3 mm |
Wall thickness | 2.0 mm |
Section size | 32×30 mm |
Fabrication | Die designing→Die making→Smelting&alloying→QC→Extruding → Cutting → Heat Treatment→QC→Surface treatment→QC→Packing→ QC→Shipping→After Sale Service |
Deep Processing | Precision cutting/CNC / Punching / Checking / Tapping / Drilling /Milling |
Certification | ISO9001 |
Our company has two departments-technical & producing department and trade department. Specializing in titanium materials and stainless steel products research and development, production and marketing services. We mainly produce and provide standards based on international standards and China's high-quality titanium and stainless steel products---- titanium sheets, titanium rods, titanium tube, titanium wire, titanium foil, titanium standard parts and other non-standard parts titanium, stainless steel tubes, stainless steel wire and other stainless steel products. Company production factory is located in the suburbs, now has a staff of 200 people, plant area of 100000 square meters;Company sales in the export sector, zhangjiagang channel int'l co.,ltd in urban areas, the existing staff 10 to 20 people.We will continue to innovation, sincere communication with all partners, create the biggest value for customers, welcome to contact us.
A. Our company is an integrated set of industry and trade company.
Q. How to ensure the quality of your products?
A. IS09000, client requirements, product standards, strict inspection to control raw material, production process and final
products.
Q. How do you resolve the problem about your products?
A. Person of aging services: For customer complaints commissioner set up a special complaint handling, complaint issues recorded
the first time and find the relevant person in charge of the feedback and resolve. Details check our "Quality
corrective action report".
Q. What is the MOQ?
A. It depends, different products will be different Sample order is acceptable, and some samples can be free.
Q. How long do you need the delivery time?
1)Supply within 5 -10 days (If products are in our stock list).
2)Customized products need to be calculated according to the quantity.
Q.What 's your payment terms?
A. T/T, L/C at sight , Western Union.
Q.How can we get your price ?
A. We need below information to quote for you:
1. Product Name
2. Standard
3. Material Grade (Chemical Composition)
4. Dimension
5. Quantity
6. The Drawing for Special Parts